Cornices, plinths, chair rails, shadow gaps and banded render lines all give a facade its character. In Revit you don't need to model these as separate extrusions. The program has two purpose-built tools: wall sweeps, which add a profile along a wall, and wall reveals, which cut a profile into it. This guide shows how to create both, either on individual walls or built into a wall type, and how to keep them under control afterwards.
Sweeps vs Reveals: What Is the Difference?
A wall sweep is a continuous profile that projects from the face of a wall. Think of skirting boards, crown mouldings, string courses or a base plinth. A wall reveal is the opposite: Autodesk describes it as a decorative horizontal or vertical cutout, so it removes material from the wall instead of adding it. Recessed joints in precast panels or render are classic examples.
Both tools follow the same logic. The shape comes from a profile family, the run can be horizontal or vertical, and you choose between two workflows:
- Instance method: place a sweep or reveal on selected walls from a 3D or elevation view. Best for one-off details.
- Type method: add it to the wall type's structure so every wall of that type gets it automatically. Best for repeated details such as a plinth on all external walls.
How to Add a Wall Sweep or Reveal to Individual Walls
The instance tools live under the Wall drop-down. According to Autodesk's help, the steps are the same for sweeps and reveals, apart from the tool you start:
- Open a 3D view or an elevation view where the wall is visible. For reveals, Autodesk specifies a 3D view or an elevation that is not parallel to the wall.
- Go to Architecture tab > Build panel > Wall drop-down and choose Wall: Sweep or Wall: Reveal.
- Pick the sweep or reveal type in the Type Selector.
- On the Modify | Place contextual tab, in the Placement panel, choose Horizontal or Vertical.
- Hover over the wall to preview the location, then click to place it.
- Keep clicking adjacent walls: Revit preselects the matching height on each one. In 3D, rotate the model with the ViewCube to wrap a band around the whole building.
- To start a new run elsewhere, use Wall Sweep Restart (or the reveal equivalent) in the Placement panel.
- Click Modify or an empty area of the view to finish.
Need to extend or trim a run later? Select the sweep in a 3D view and use Add/Remove Walls on the contextual tab, then click walls to include or drop them. You can also drag the end grips to shorten a run, or adjust the level and offset values in the instance properties.
How to Build Sweeps and Reveals into a Wall Type
When a detail should appear on every wall of a type, put it in the type itself. This is the cleaner choice for office standards, because the plinth or joint follows the wall wherever it is drawn.
- Select a wall and click Edit Type in the Properties palette. Duplicate the type first if other walls should stay unchanged.
- Click Preview to open the preview pane and set the view below it to Section. The vertical structure tools only work in the section preview.
- Click Edit next to the Structure parameter to open the Edit Assembly dialog.
- Under Modify Vertical Structure, click Sweeps or Reveals, then Add.
- Choose a profile. Sweeps get their own material; reveals have none, because they take the material of the layer they cut.
- Set Distance and whether it is measured From the base or top, then pick the Side (exterior or interior).
- Fine-tune with Offset (negative values move toward the core), Flip and Setback, which keeps the profile back from doors and windows.
- Click OK and check the result in a 3D view.
For sweeps, two extra checkboxes matter. Cuts Wall cuts the sweep's geometry out of the host wall; Autodesk notes that clearing it can improve performance in big models. Cuttable lets inserts such as windows cut through the sweep.
Changing Profiles and Practical Tips
The look of a sweep or reveal is driven by its profile. To swap it, select the element, click Edit Type, set the Profile parameter to another profile type and click OK. Because this is a type parameter, every sweep of that type updates at once, so duplicate the type if you only want to change some of them.
A few habits that save time:
- Name types clearly, for example "Sweep - Plinth 150" or "Reveal - 20 Shadow Gap", so the Type Selector stays readable.
- Use the type method for repeated details. It avoids dozens of loose instances that need fixing whenever walls move.
- Check wall joins and corners in 3D. Wrapping a band around adjacent walls in one session usually gives tidier corners than placing separate runs.
- Watch performance. On large models, consider clearing Cuts Wall on sweeps where the cut adds nothing to your drawings.
If you manage many wall types and families, add-ins can speed up the housekeeping around them; our pyRevit 7.0 review covers one popular free option, and our list of top Dynamo nodes helps when you want to automate repetitive edits.
Conclusion
Wall sweeps add a profile and wall reveals subtract one, and both can be placed per wall or built into a wall type. Use the Wall: Sweep and Wall: Reveal tools for quick, one-off details, and the Edit Assembly dialog for standards that should travel with the wall. Get the distance, side, offset and setback right once, and Revit will carry your cornices and shadow gaps across the whole model.
.png)